By Phoebe | 09 January 2018 | 0 Comments
Programming Instructions for GOH-PCGEN2 Mazda remote fob
Programming Instructions:
Method #1
1. Open the driver side door
2. Lock and then unlock the door using the button on the door.
3. Leave the door open.
4. Insert a key into the ignition and turn the car to the ON position. Leave for about 2 or 3 seconds, then turn off. Repeat this two more times (3 in total). Leave the key in the slot in the OFF position.
5. Close the driver’s door. Then open it. Then close it. Then open it. Then close it. Then open it.
6. The onboard computer will respond by locking and unlocking all the doors at this point. That means it’s ready to accept FOB programming
7. Press a button on each FOB unit to program it to the computer.
When you are done programming FOBs, you can simply remove the key, which causes the computer to cycle the door locks once more.
Method #2
1. Remove key from ignition.
2. Close all doors.
3. Open driver side door and leave open.
4. Perform the following steps within 24 seconds.
a. Insert key in ignition.
b. Turn key to ON and OFF.
c. Repeat step b two more times.
d. Remove key.
e. Push driver door frame button three times (black rubber button located on driver door frame that tell the vehicle whether or not door is closed.)
5. Buzz sound, chime or doors will lock and unlock should be heard at this point signaling that the vehicle is now in programming mode. If not, wait 40 seconds and return to step 4.
6. All transmitters need to be programmed at this time, including the old ones. Push any button on the transmitter two times. A buzz sound, chime or doors locking and unlocking should be heard at this point signaling that the vehicle has accepted the new transmitter code. If there is only one transmitter, repeat this step two more times using the only transmitter. If there are two transmitters, repeat this step two more times using the second transmitter.
7. Push driver door frame button one time. Two buzz sounds, chimes or doors locking and unlocking 2 times should be heard at this point signaling successful programming.
Method #1
1. Open the driver side door
2. Lock and then unlock the door using the button on the door.
3. Leave the door open.
4. Insert a key into the ignition and turn the car to the ON position. Leave for about 2 or 3 seconds, then turn off. Repeat this two more times (3 in total). Leave the key in the slot in the OFF position.
5. Close the driver’s door. Then open it. Then close it. Then open it. Then close it. Then open it.
6. The onboard computer will respond by locking and unlocking all the doors at this point. That means it’s ready to accept FOB programming
7. Press a button on each FOB unit to program it to the computer.
When you are done programming FOBs, you can simply remove the key, which causes the computer to cycle the door locks once more.
Method #2
1. Remove key from ignition.
2. Close all doors.
3. Open driver side door and leave open.
4. Perform the following steps within 24 seconds.
a. Insert key in ignition.
b. Turn key to ON and OFF.
c. Repeat step b two more times.
d. Remove key.
e. Push driver door frame button three times (black rubber button located on driver door frame that tell the vehicle whether or not door is closed.)
5. Buzz sound, chime or doors will lock and unlock should be heard at this point signaling that the vehicle is now in programming mode. If not, wait 40 seconds and return to step 4.
6. All transmitters need to be programmed at this time, including the old ones. Push any button on the transmitter two times. A buzz sound, chime or doors locking and unlocking should be heard at this point signaling that the vehicle has accepted the new transmitter code. If there is only one transmitter, repeat this step two more times using the only transmitter. If there are two transmitters, repeat this step two more times using the second transmitter.
7. Push driver door frame button one time. Two buzz sounds, chimes or doors locking and unlocking 2 times should be heard at this point signaling successful programming.
Leave a Reply
Your email address will not be published.Required fields are marked. *